AC permanent magnet motor and control experimental device

It is m--nly composed of car AC permanent magnet motor, motor controller, gear switch, accelerated pedal, ignition switch, power supply and fault setting system.

2. Product function

1. Cognition of car AC permanent magnet motor and controller;

2. The structure and principles of car AC permanent magnet motors and controllers;

3. The manifestation of the driver's intention and the operation of permanent magnet motor;

4. Settings and assessment of common faults;

5. Equipped with a complete experimental manual.

3. Product specifications

1. The shape size is 1240 × 600 × 1700mm;

2. Power: 220VAC/50Hz;

3. The rated power of the motor: 4KW;

4. Motor rated speed: 3000rpm;

5. Motor working voltage: 72VDC;

6. The upper part of the box is formed as a whole, and the surface is rust -proof and p--nted; the lower part is welded by 40*40 square tube;

7. Use the UV tablet inkjet panel with a thickness of not less than 4mm. The color circuit diagram is not refunded and wear -resistant;

8. Two thousand -or two -directed foot wheels are installed at the bottom, equipped with brakes to facilitate the movement and fixing of the device.

9. Machinery assembly and fitter assembly virtual simulation software: This software is developed based on Unity3D. It can select 6 -level image quality. It has the design and virtual disassembly of the reducer and shaft structure, the design and simulation of common mechanical institutions, institutional resource libraries, institutional resource libraries. Typical mechanical institutions (virtual disassembly of gasoline engines), software is an overall software, which cannot be separate resources.

A. Turbine design and virtual disassembly interface can be selected from turbine sn--l pole cone gear reducer, second -level pilot gear reducer, conical cylindrical gear reducer, coaxial cylindrical gear reducer, cone gear reducer, first -class cylindrical, first -class cylindrical, Gear reducer.

1. Technical specifications:

Shape size: 600mm long, 530mm wide, high 1800mm high

Voltage/power: AC 220V/50W

Supporting equipment: 6U network pressure wiring experimental 1, 6U network jumping line detection and f--lure demonstrator, 2 network rag ring ring, 8 PDU power sockets, 100 rounds 110 communication jumping line frames, 2 units Two network wiring racks, 1 optical fiber wiring frame, 1 part/tool box, and 1 set of power areas.

2. Product characteristics

1) The device is selected from the 19 -inch open floor frame. The shape size: 0.6 meters long, 0.53 meters wide, 1.8 meters high. The lower part of the rack is fixed to the foot screws, ensuring that the equipment is firm and can withstand the impact of tr--ning lines.

2) 6U rack type color LED color block display function network pressure wiring tr--ning tester (color LED color block display light, a total of 96), each core wire is connected to the corresponding color LED light block, intuitive continuous display display display The connection status and line order of the end connection. There are 96 luminous colors in 48 groups. At the same time, all end connection conditions of the six twisted lines are displayed, and it is intuitively judged that the cross -connection, anti -connection, short circuit, and disconnection of the communication network twisted line. The test results were transmitted to the Teacher's computer management side software with the WiFi wireless signal or RS485.

One of the network jumping line detection and fault demonstrators of the color LED display function, corresponding to the connection status and line order of the colored LED light luminous block display of the two ends of the RJ45 connector. Each jump corresponds to the 16 colored LED luminous color blocks of 8 groups, and the connection status and line order are visually continuously displayed. It is divided into 32 groups with 64 luminous color block lamps, and there are cable types, groups, and fault type prompt lamps. , Quickly detect 4 jumper pressure connections at the same time. F--lure simulation demonstration functions, set 6 groups (correct, anti -connection, cross, interruption, cross, short circuit) common network wiring correct and fault types. The test results were transmitted to the Teacher's computer management side software with the WiFi wireless signal or RS485.