Direct spray engine+dual -clutch transmission comprehensive training desk

 

Based on the electronic control engine and the dual -clutch automatic transmission, the engine can be performed on the engine, acceleration, and deceleration and other operating conditions. Work conditions practice and perform stall experiments. It can truly display the structure and work process of electronic control gasoline engines and dual -clutch automatic transmission.

Applicable to the teaching needs of the theory and m--ntenance tr--ning of automotive engines and dual -clutch automatic transmission theory and m--ntenance tr--ning for medium and higher vocational and technical colleges, ordinary education institutions and tr--ning institutions.

 

2. Functional characteristics

1. Real -operated electronic control gasoline engine and dual -clutch automatic transmission, fully display the composition and working process of the electronic control engine and the dual -clutch automatic transmission.

2. The tr--ning table panel adopts the 4mm thick corrosion resistance, strike, pollution resistance, fire prevention, and moisture -proof ** aluminum -plastic panels. The surface is sprayed with primer p--nting by special processes; Intuitive control circuit diagrams and electronic control gasoline engines and dual -clutch automatic transmission physical objects, understand and analyze the working principle of the control system.

3. The tr--ning countertop is installed with car instrument, fuel pressure gauge, and vacuum pressure gauge. It can display parameters such as the engine speed, vehicle speed, automatic transmission gear, automatic transmission gear, fuel injection pressure, and --r pipe pressure.

4. The tr--ning terminal is installed on the panel, and the electrical signals that can detect each sensor, actuator, and engine control unit pipe foot can be detected directly on the panel, such as resistors, voltage, current, frequency signals, etc.

5. The tr--ning desk is installed with a diagnostic seat, which can be connected to a dedicated or universal car decoder. , Parameter setting, waveform analysis and other self -diagnosis functions.

6. The tr--ning table is equipped with a throttle control device, which can be convenient to accelerate the engine.

7. The tr--ning table is equipped with a braking system (braking pedal, braking total pump, braking split pump, brake disc). The output shaft can perform a stalling experiment for automatic transmission, and detect the power parameters of the engine and automatic transmission.

8. The tr--ning desk is equipped with installation protection devices such as total power switch, water tank protective cover, output shaft protective cover.

9. The device detection panel is equipped with a 20cm steel table on the front base in front, which is convenient for placing data and detection instruments.

10. The bottom of the tr--ning platform is welded with steel structure, the surface is treated with spraying process, and a self -locking wheel device is welded in front/sides.

11. Machinery assembly and fitter assembly virtual simulation software: This software is developed based on Unity3D, which can choose 6 -level image quality. It has the design and virtual disassembly of the reducer and shaft structure, the design and simulation of common mechanical institutions, institutional resource libraries, institutional resource libraries. Typical mechanical institutions (virtual disassembly of gasoline engines), software is an overall software, which cannot be separate resources.

A. Turbine design and virtual disassembly interface can be selected from turbine sn--l pole cone gear reducer, second -level pilot gear reducer, conical cylindrical gear reducer, coaxial cylindrical gear reducer, cone gear reducer, first -class cylindrical, first -class cylindrical, Gear reducer.

1. Experimental purpose:

1. Deepen the understanding of "printing and dyeing wastewater" or other wastewater.

2. Master the performance and testing technical data of this process, and use reliable data into production.

3. Make the operator improve theoretical and practical knowledge.

2. Experimental principle:

This device adopts the A/O method biochemical treatment process, which is two stages: hypoxic acidization and contact with oxidation.

After the sewage is removed from large particles and fiber -like impurities, it flows into the water tank (the large amount of water can be stirred by a fan), and then enters the acidification pool through the pump and measure the acidification pool for acidic hydrolysis. At this stage, the sewage is m--nly mass -quality. And using the characteristics of short -generation oxygen generations, strong activity, and easy reproduction and growth, the large molecular structure organic objects that are not easy to degrade into small molecules and soluble compounds, initially degraded organic matter, and at the same time completed the nitrification effect. pollute.

Contact oxidation pool is a biological treatment device based on biofilm method -based and active sludge method. Through the aeration of oxygen oxygen, the organic matter in the sewage is fully exposed to the biofilm in the pool. The degradation function further degrades the small molecules and soluble compounds into carbon dioxide and water; then enters the vertical streaming two sinking pools to remove the peeled biofilm and active sludge, so that the water can reach the standard.

3. M--n technical indicators and parameters: (Reference):

1. Environmental temperature: 5 ～ 40 ℃

2. Treatment of water: 15 ～ 30L/h

3. Water inlet: CODCR 300 ～ 500mg/L Out of Water: 30 ～ 50 mg/L

4. Water inlet: BOD5 100 ～ 250 mg/L Out of water: 15 ～ 30 mg/L

5. Water inlet: SS 100 ～ 200 mg/L Out of Water: 15 ～ 30 mg/L

6. Water inlet: pH value: 6.5 ～ 8.5 out of water: 6.5 ～ 8.5

7. Work power supply 220V, safety protection: have ground protection, leakage protection, overcurrent protection;

8. Electrical line installation requirements: layout tanks, power cords, control lines and other wires are standardized, which have the characteristics of insulation and arc -proof;

9. Device shape size: 1600mm × 700mm × 1900mm.

10. Work power: AC220V ± 10%, 50Hz, single -phase three -line system, 1100W power, safety protection: ground protection, leakage protection, overcurrent protection