Bio adsorption process training device

Adsorption regeneration method is also called contact stability or bi adsorption method. The m--n characteristic of this operation method is the two processes of degradation of active sludge -degradable organic matter -the initial adsorption and biological metabolism are built in one structure. After the regeneration, the active sludge and the sewage enters the adsorption pool together. In the adsorption tank, the adsorption pool is fully mixed through 30 to 60min to complete the adsorption process. To the regeneration pool, complete the biological metabolism process, restore the activity sludge recovery and adsorption performance, and then enter the adsorption pool for the next cycle. A structure is built in the adsorption pond and the regeneration pool, which is carried out in two sections.  

2. M--n technical indicators and parameters:

1. Environmental temperature: 5 ℃ ～ 40 ℃

2. Treatment of water: 10L/H,

3. Device shape size: 1600 × 500 × 1400mm,

4. Work power: AC220V ± 10%, 50Hz, single -phase three -line system, 500W power, safety protection: ground protection, leakage protection, overcurrent protection

2. M--n parameters and configuration:

1. 1 raw water tank: white PP plate material, 10mm thickness, 400 × 400 × 500mm, and the bottom plate installation valve to facilitate the cleaning of the water;

3. 1 water tank: white PP plate material, 10mm thickness, 350 × 350 × 400mm, installation valve installation of the bottom plate, which is convenient for cleaning the water;

3. With 1 set of original water tank mixing motors, one set of 304 st--nless steel mixing paddles; (power of 25W, speed 120rpm, 1 tuneing speeder),

4. 1 combination of attached pools, transparent organic glass material, 10mm wall thickness, 500 × 300 × 500mm, 1 set of aeration devices,

5. 1 regenerative pool, transparent organic glass material, wall thickness 10mm, 300 × 250 × 500mm,

6. 1 sinking pond, transparent organic glass material, wall thickness 8mm, ø250 × 350mm,

7. Two magnetic pumps for corrosion corrosion, traffic: 16 ～ 19 (L/min), r--sing: 2.7 ～ 3.4 (m) power 20W

8. 1 --r pump, power: 40 W, ** Quality: 16L/min,

9. Traffic measurement and adjustment: 1 rotor flow meter, (LZS-15, a range of 6 ~ 60L/h)

Technical indicator

1. Treatment of water: 30L/h;

2. Work power: AC220V ± 10%, 50Hz, single three -line system, power 800W, safety protection: ground protection, leakage protection, overcurrent protection;

3. Installation of power lines and control lines: Environmental protection flame retardant electrical wiring slots must be used to standardize and organize the characteristics of national standards. It has the characteristics of insulation, arc -proof, flame retardant self -extinguishing. Change the line;

4. Device shape size: 2100 × 450 × 1800mm.

M--n configuration and parameters

1. High -level water tank, average flow slot, flocculation pond, sedimentation tank, mixed slot: transparent organic glass material, thickness 10mm;

2. One of the original water tank and water tank: white PP board, 10mm thick, empty valve installed on the bottom plate, which is convenient for cleaning the water;

3. 1 mixing motor (power 25W, speed 90rpm), st--nless steel mixing paddle;

4. 1 set of electric stirring devices and 1 speed regulator;

5. Submarine pumps, flowmeters;

6. Pin drug pump, medicinal liquid box;

7. The table (white 10mm thick PP board), drawing silver double -color board signs (the m--n components of the device to compose names for students to understand the equipment);

8. Power control system: 1 double -sided sub -light -dense -dense -densely spraying electrical control box, leakage protector (Delixi), voltage meter, self -locking button switch (Zhengt--), wire grooves, etc., control box panel panels, etc. Made with aluminum concave characters;

9. AD ERA supporting connection pipes, valves, elbows;

10. The st--nless steel framework experimental desk (30*30mm st--nless steel square tube, and the foot wheels are all universal bands).